Edexcel International GCSE Physics · Section 3 Waves · 3 (d) Light and sound · Physics only
Frequency of Sound with an Oscilloscope: f = 1 ÷ T
In this lesson you'll learn to: explain how a microphone and an oscilloscope display a sound wave, read the time period off a trace using the
time-base, calculate the frequency with f = 1 ÷ T, describe the practical, and say how the trace changes
when a note gets louder or higher.
Physics onlyDon't read anything yet. On tab 1, slide the frequency up and watch the waves
squash together, then change the time-base to spread them out again. Press Hear it. On tab 2, a note is hiding behind
"??? Hz": drag the gold cursors across 10 waves and work out what it is. Tab 3 shows louder against higher.
Time-base
waves on the screen5
time period, T2 ms
f = 1 ÷ T500 Hz
one wave covers2 divisions
ms Hz
Drag the two gold cursors so they sit on the same point of the wave, 10 waves apart. Read the divisions between them, then work out T and f.
Change the note
▲ The trace is drawn from the real time-base: one wave covers T ÷ time-base divisions.
Found the mystery note? Now learn the method for the exam.
Count the divisions for 10 waves, multiply by the time-base, divide by 10 to get T, then f = 1 ÷ T with T in seconds.
How a microphone and an oscilloscope show a sound (3.26P)
The microphone changes the sound into an electrical signal (a voltage that goes up and down with the sound).
The oscilloscope draws that voltage: voltage up the screen against time across it.
The trace looks like a transverse wave, but the sound itself is still longitudinal. The screen shows how the voltage changes with time.
Workbook page 17: signal generator → loudspeaker → microphone → oscilloscope. Here 10 waves cover 8.0 divisions at 0.5 ms/div.
Reading the screen
Control or feature
What it tells you
time-base (ms/div)
the time for one square across. Time = number of divisions × time-base.
volts/div
the voltage for one square up. Turn it to make the trace taller or shorter.
height of the waves
the amplitude: a taller trace is a louder sound
number of waves on the screen
the frequency: more waves is a higher pitch
🔊
Louder, same pitch
The waves get taller (bigger amplitude). The number of waves on the screen stays the same.
🎵
Higher pitch, same loudness
More waves fit on the screen, each one narrower (bigger frequency, smaller T). The height stays the same.
The practical (3.27P)
Connect the loudspeaker to the signal generator. Connect the microphone to the oscilloscope.
Hold the microphone in front of the loudspeaker so the sound shows as a trace.
Adjust the time-base until there are at least 10 complete waves on the screen.
Count the number of squares (divisions) for 10 complete waves.
Time for 10 waves = number of squares × time-base. Divide by 10 to get the time period, T.
Calculate the frequency using f = 1 ÷ T, with T in seconds.
Why 10 waves, not one? Reading one wave off the grid has a big percentage error. Timing 10 and
dividing by 10 reduces the (percentage) error, so T, and f, are more accurate.
⭐ Two things that lose marks
ms into s. f = 1 ÷ T only gives hertz if T is in seconds: 0.40 ms = 0.000 40 s.
Forgetting to divide by 10. The time for 10 waves is not the time period.
✍
How to write it in the exam
The chain for "find the frequency from the trace"
Count the divisions for 10 waves → × time-base = time for 10 waves →
÷ 10 = T → change T into seconds → f = 1 ÷ T, in Hz.
read the screenthe workingthe answer
Workbook page 17 · analysis · use the trace above
10 waves cover 8.0 divisions. The time-base is 0.5 ms/div. Find the frequency.
time for 10 waves = 8.0 × 0.5 ms = 4.0 ms T = 4.0 ÷ 10 = 0.40 ms = 0.000 40 s
f = 1 ÷ 0.000 40 = 2500 Hz
Workbook page 17 · exam-style question · 8 marks
A student connects a microphone to an oscilloscope and plays a note from a loudspeaker. The time-base is 1 ms per division.
(a) State what the microphone does. (1) changes the sound into an electrical signal (voltage)
(b) Use the trace to find the time period. (2) one wave = 2 divisions (1); T = 2 × 1 ms = 2 ms (0.002 s) (1)
(c) Calculate the frequency. (2) f = 1 ÷ T = 1 ÷ 0.002 (1) = 500 Hz (1)
(d) The note is made louder without changing its pitch. Describe how the trace changes. (2) the waves are taller: the
amplitude increases (1); the number of waves on the screen stays the same (1)
(e) Why measure the time for several waves, not just one? (1) it reduces the (percentage) error, so T is more accurate
Check your answer has all its parts: divisions × time-base, ÷ 10 if you timed 10 waves,
T in seconds, then f = 1 ÷ T in Hz. For "louder": taller, same number of waves. For "higher pitch": more waves, same height.
📘 Now do it in your workbook
Page 17: label the set-up, fill in the method, read 10 waves off the trace to find the frequency, and an 8-mark exam-style question.